Fabtech 2019+ Ram 1500 6" Basic Lift Kit # K3086
This Fabtech 6" Basic Lift System is designed for use on the 2019 and newer Ram 1500 4x4 trucks and will clear up to a 37" tire. This system is a great choice for Ram owners looking to retain the stock ride yet want big tires and wheels. The factory suspension is relocated with heavy duty bolt on bracketry that will provide years of trouble free service. The system features Fabtech’s proven IFS technology with extended length ductile iron steering knuckles for proper factory electronic stability control functionality. Heavy duty 1/4” thick steel lower control arm crossmembers provide superior ground clearance while the integrated front differential skid plate adds protection to the drivetrain. Rear lift is accomplished with steel coil spring spacers that utilize the factory coil springs for stock load carrying capacity with a great highway ride.
Please keep reading below for more information...
Manufacturer | Fabtech Motorsports |
---|---|
Part Number | K3086 |
Vehicle Year | 2019 |
Vehicle Make | RAM |
Vehicle Model | Ram 1500 |
Drive Type | 4-Wheel Drive |
Made In USA | Yes |
Fabtech 2019+ Ram 1500 4x4 Basic Series 6" Lift System # K3086 is designed to fit the recently updated 2019 model year Ram 1500 trucks. With an additional 6" inches of vehicle suspension ride height you can pretty easily clear most 35" tires and with some light trimming you can run up to a 37" tire. This Fabtech system is designed to retain the factory on and off-road capability of your Ram by retaining the front shock and spring assembly and replacing the rear shocks with a set of Fabtech Performance Series (white can) shock absorbers.
Vehicle Fitment Information:
For coil spring suspension trucks only - WILL NOT FIT AIR RIDE MODELS! Fabtech designed and built this 6" lift using the standard height Ram 1500 4x4 truck. Due to differences between the 2wd and 4x4 trucks this Fabtech lift will NOT fit any 2wd model Ram 1500. This lift will NOT fit the 2019 Classic edition Ram 1500 trucks built on the older chassis. If your Ram 1500 4x4 has the factory installed Off-Road Package (+1" lift from the factory) your actual lift height increase should be close to 6" inches over the current height. That means your ORP equipped truck will sit approximately 7" inches higher in the front than a standard Ram 1500 4x4.
Ram 1500 Rebel Information:
This lift is not recommended for use on Rebel edition Ram 1500 4x4 trucks. This is because the Rebel already has a +2" lift from the factory that is achieved by using a different front shock and spring assembly. The operating angle on the components is in our opinion too steep and could lead to premature wear and problems with the front axle shafts, tie rods ends and the upper control arm. If you absolutely have to lift your Rebel we'd recommend you look at the Fabtech Performance 6" Lift with Dirt Logic coilovers instead.
Fabtech K3086 Contents:
1 x FTS23200 = Component Box 1
1 x FTS23201 = Component Box 2
1 x FTS23038 = Component Box 3
2 x FTS7348 = Rear Performance Series Shocks
Kit Features:
Crossmembers: 1/4" thick steel lower control arm crossmembers are arched for maximum ground clearance. Four adjustable alignment cams provide a wide range of adjustment. The fully welded box design of these crossmembers provides additional strength to the front suspension.
Steering Knuckles: Extended length ductile iron steering knuckles retain near stock track width keeping the tires under the fenders. These steering knuckles are designed to work in conjunction with the factory ESC for proper functionality at all speeds.
Skid Plate: A heavy duty front differential skid plate is constructed of 1/4” thick steel to protect the diff from offroad obstacles.
Differential Mounts: Integrated differential mounts on the crossmembers properly reposition the front diff for the precise CV and driveshaft angle throughout the entire steering and suspension travel range.
Sway Bar Brackets: Heavy duty drop brackets retain the factory link ends at the correct angle for a positive road feel without creating binding at full droop.
Rear Coil Spring Spacers: Steel rear spring spacers utilize the factory coil springs retaining the stock load carrying capacity and ride comfort.
Rear Track Bar Bracket: The bolt on relocation bracket re-centers the rear axle for the new ride height while retaining the factory roll center of the vehicle.
Tire & Wheel Information:
The OEM wheel and tires are NOT compatible with this Fabtech 6" Lift. You must use aftermarket 20" or larger diameter wheels. Will NOT fit vehicles equipped with factory OEM 22" wheels and the heavy duty "XL" bearing option.
Recommended Tire Size – 35/12.50R20 Wheel Size – 20×9 wheels w/ 5” BS w/ minor trimming
Recommended Tire Size – 37/12.50R20 Wheel Size – 20×9 wheels w/ 5” BS w/ minor trimming
For more information please click on the "Ask A Question" link located at the very top of this page.
Manufacturer | Fabtech Motorsports |
---|---|
Part Number | K3086 |
Vehicle Year | 2019 |
Vehicle Make | RAM |
Vehicle Model | Ram 1500 |
Drive Type | 4-Wheel Drive |
Made In USA | Yes |