Pedal Commander 2019+ Ram Truck Throttle Response Controller # PC78-BT

Pedal Commander Throttle Response Controller # PC78. This product fits all of the new 2019 and up Ram trucks. This part number will NOT fit 2019 Classic Edition trucks.

How does this product work?
The Pedal Commander # PC78 is a plug and play device that intercepts the electronic signal that your accelerator pedal sends to the Engine Control Unit (ECU). It then alters the signal to allow for more rapid engine acceleration which in turns provides you with better vehicle acceleration. Newer Ram vehicles utilize a"fly by wire" throttle that doesn't have a direct mechanical connection to the throttle body like older vehicles. To make acceleration smoother the factory engineers will program the computer system to provide a very lazy acceleration profile. While this does provide a level of comfort it can cause your Ram to feel slow and sluggish. If you want to wake up your trucks performance without actually installing potentially warranty voiding power adders the Pedal Commander is your best option. Your engine still makes the same amount of horsepower and torque as before but you get the feeling that ALL of that power is available right NOW instead of waiting for the factory ECU to slowly deliver it over time. This results in a MUCH more enjoyable vehicle to drive... and it won't void your warranty!

How easy is installation?
In a word, easy! Each Pedal Commander PC78 is custom built for use with specific vehicles. Vehicle specific wiring harness and programming is included. Installation takes about 10 minutes and usually requires no tools. A flashlight and a good set of glasses may be helpful if your eyes aren't as great as they used to be. The basic installation goes something like this... turn the ignition off and remove the key and let the vehicle sit for a minimum of 5 minutes. This allows the computer systems and accessories to power down completely. If your vehicle is equipped with a keyless entry remote make sure that it is located well outside of its operating range. These remote keys can cause the factory computer systems to activate even though the ignition is in the off position. Failure to follow these basic steps can cause problems after the Pedal Commander is installed. The next step is to disconnect the factory wiring plug at the accelerator. You then connect the factory wiring to the Pedal Commander and connect the wiring harness coming out of the Pedal Commander directly to the accelerator. That's it, the device is now installed!

Frequently Asked Questions...

Does Pedal Commander # PC78 harm my engine?
The Pedal Commander does not increase the engine horsepower or torque of your engine. The power output is not altered. This device works by removing the factory "lag" that is programmed into the accelerator and ECU. This product does NOT modify the fuel or timing values. All factory protection features of the engine remain in place. Pedal Commander will only be activated when you really need the power (like when you accelerate) and Pedal Commander will not function when the accelerator is not depressed, such as when idling in traffic or at a stop light.

Can Pedal Commander # PC78 be used on new or high mileage vehicles?
You can use Pedal Commander regardless of the mileage of your vehicle. Due to the digital protection technology of your original ECU. ou take no risk. Dealerships and fleet managers are installing these units in brand new vehicles. You should always observe the run-in period as recommended by the manufacturer. Customers have installed Pedal Commander on vehicles with well over 100,000 miles without issues. If your vehicle is mechanically sound and in good operating condition the Pedal Commander will simply enhance the driving experience of your order vehicle.

Can Pedal Commander # PC78 be detected when the vehicle is taken in for service?
No, Pedal Commander cannot be detected. After the removal of Pedal Commander it is not detectable and the vehicle is immediately returned to its original performance and calibration. No permanent hardware or software changes are ever made when using Pedal Commander. This makes Pedal Commander ideal for leased or company vehicles. The operation is not traceable as it does not leave a digital foot print after it is removed from the vehicle.

Is the Pedal Commander # PC78 compatible with aftermarket tuners or reflashed ECU's?
Yes! The Pedal Commander is compatible with aftermarket tuners and programmers. The Pedal Commander only modifies the throttle pedal signal which means it is virtually invisible to your tuner. If you are running a modified ECU the Pedal Commander will still provide 100% functionality.

What is the warranty on the Pedal Commander # PC78?
Pedal Commander will replace any faulty or defective unit within 2 years of the original purchase date! Each unit also qualifies for any available software updates that may be released during the first 2 years of ownership.

For more information on this or any other Pedal Commander product please click on the "Ask A Question" link located at they very top of this page.

This item ships for FREE to any address in the United States of America!