Pro Comp 2011 - 2019 GM 2500HD 6" Lift # K1085M
This Explorer ProComp K1085M 6" suspension lift is designed for use on the 2011 - 2019 model year Chevrolet Silverado 2500HD and GMC Sierra 2500HD trucks. This kit will NOT fit the 2010 or earlier model year trucks. Pro Comp tried to incorporate a high torsion system in their new kit, however several things became apparent. One, the added stress by moving the control arm down, and leaving the torsion up, introduced additional load on the control arm bushings and torsion riser. The initial 1/4" thick adapter was bending while driving on local roads, so ProComp increased the thickness to 3/8" and tested at the desert. After one-hour and forty minutes of driving in desert whoops (minimal speed) the new torsion riser showed signs of bending. Further investigation revealed additional wear to components not seen when using the conventional torsion drop. So Procomp decided that Function was more important than Form... and that means should you decide to take your HD off-road this lift design won't let you down!
Keep reading below for more product details...
| Brand | Pro Comp Suspension |
|---|---|
| Manufacturer | Pro Comp Suspension |
| Part Number | K1085M |
| MPN | K1085M |
| GTIN | 614901342215 |
| Vehicle Year | 2019, 2018, 2017, 2016, 2015, 2014, 2013, 2012, 2011 |
| Vehicle Make | Chevrolet, GMC |
| Vehicle Model | Sierra 2500HD, Silverado 2500HD |
| Drive Type | 2-Wheel Drive, 4-Wheel Drive |
| Made In USA | Yes |
Pro Comp Suspension 6" Lift # K1085M is designed to fit 2011 - 2019 model year Chevrolet Silverado 2500HD and GMC Sierra 2500HD trucks. This kit is relatively easy to install and Pro Comp went to great lengths to build a kit that doesn't require drilling. Anywhere they could the factory holes were used. When additional holes were needed, Pro Comp devised interlocking features to obtain satisfactory mounting while easing installation. To make DIY installation possible NO welding is required. The new HD comes with additional mounting points for the rear cross member, allowing ProComp to design a lift that does not require a welded in support plate. One Cut... There is only one vertical cut required to the driver side differential frame horn.
Largest rear cross member ever... At first glance the 2011 - 2019 HD looks like any other truck. However with further inspection, ProComp found that this is the largest HD that Chevrolet has ever produced. This calls for the largest cross member that ProComp has ever made. At over four feet long, and over 50 lbs, this cross member is ready for the toughest tasks.
Overkill u-bolts... GM supplied the new HD with 18mm u-bolts, ProComp did one better, and increased their u-bolts size to 3/4" inch.
A place for everything... Detailed thought goes into everything that needs to be re-located. Even the smallest detail like brake line tabs and ABS clips get a new home, so you can trust your new K1085M lift will not compromise safety.
Wider is better... When raising a vehicle 6" the truck becomes top heavy from raising the center of gravity and the CG is directly related to the Stabilitrak system. By widening the vehicle 3/4" per side, ProComp can maintain the factory king pin inclination, which helps stabilize the truck and work with the Stabilitrak, not against it. In addition to working with the Stabilitrak, no additional tire scrub is added.
Factory 20" wheels can be used with the K1085M suspension lift.
For more information on this or any other Explorer ProComp product, please click on the "ask a question" link located at the very top of this page.
This item ships for FREE via Standard Ground Service to any address in the contiguous 48 United States of America!
| Brand | Pro Comp Suspension |
|---|---|
| Manufacturer | Pro Comp Suspension |
| Part Number | K1085M |
| MPN | K1085M |
| GTIN | 614901342215 |
| Vehicle Year | 2019, 2018, 2017, 2016, 2015, 2014, 2013, 2012, 2011 |
| Vehicle Make | Chevrolet, GMC |
| Vehicle Model | Sierra 2500HD, Silverado 2500HD |
| Drive Type | 2-Wheel Drive, 4-Wheel Drive |
| Made In USA | Yes |
